Earthway S25ss SPRAY-PRO PUSH SPRAYER Bedienungsanleitung PDF herunterladen

Rotate wheel

to help

install pins

Steel Ring

Flat Washer

Slide one knurled pin into each slot

in the hub and then spray with WD-40

or a light oil and slide wheel in fully and

secure with a cotter pin

1” Cotter Pin

Coast Wheel

Drive Wheel

1” Cotter Pin

S25ss

SPRAY-PRO PUSH SPRAYER

ASSEMBLY and OPERATING INSTRUCTIONS

SPRAY-PRO

EarthWay

Lower

Handle

Axle Bushing

Congratulations on the purchase of this new sprayer from Earthway Products, Inc. Please call us if you have any difculty

with assembly or operation of this sprayer. We can be reached via the telephone at 800-294-0671 or 574-848-7491, Monday

- Friday 9:00am ~ 4:00pm or visit us online at www.earthway.com This sprayer comes with lifetime technical support,

email us at techsupport@earthway.com.

HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY

THIS SPRAYER COMES PARTIALLY ASSEMBLED, REQUIRING YOU TO INSTALL THE WHEELS, HANDLE ASSEMBLY,

SPRAY GUN HOLDER, AND CONTROL ROD. IT SHOULD TAKE APPROXIMATELY 15 MINUTES WITH THE USE OF TWO

7/16” WRENCHES AND 1 PAIR OF PLIERS.

5 Your sprayer is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds

will change the spray patterns and output volumes that you will achieve.

5 Clean your sprayer tank thoroughly after each use. Wash with clean water and push sprayer several feet to evacuate any

residual materials until you see clean water. Do this in a safe area as described in the chemical supplier directions.

5 Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.

5 Check all hose connections regularly to ensure they remain tight.

5 If unit fails to spray on initial use, or leaks from the nozzle, remove the cap from the top of the DCV, wipe off the top of

DCV body to remove any debris, and then replace the cap and tighten.

5 Coat all metal surfaces (inside & outside of chassis) with light oil or silicon spray to help prevent corrosion.

5 When the tank is empty, PULL THE SPRAYER BACKWARD to the designated cleaning or storage area to prevent

damage that can occur with a dry pump.

2. Turn the S25 upside-down on to the tank.

3. Ensure that the Axle Bearings are pushed into the Axle Bushing on both sides as shown

at the right. Install the Coast wheel (this wheel does not have the steel ring on the inside

hub as shown below) on to axle using the cotter pin hole closest to edge of the axle.

Insert 1” cotter pin through the axle and bend with pliers to prevent pin from falling out.

Cotter Pin

Locations

1-2012 Pt. # 52230SS PAGE 1

1. Open carton and remove the Handles, Control Rod, Hardware pack, Wheels, and the

S25 from carton.

4. Install the at washer onto the axle and slide to the lower

handle. Next, position the drive wheel onto the axle 2” and

install the three (3) knurled pins one into each slot located

between the hub and the axle as shown at the right, coat the

knurled pins with WD-40 or a light oil, nish by sliding the

wheel tight against the lower handle. Now insert 1” cotter

pin through axle, bend with pliers to prevent cotter pin from

falling out.

NOTE: Included is extra set of Knurled Pins (S25-30003)

which should be saved for future use. These are wear items

and will need to be replaced at some time. Replacements are

available to purchase directly through our Parts department.

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - EarthWay

Rotate wheel to help install pinsSteel RingFlat WasherSlide one knurled pin into each slot in the hub and then spray with WD-40 or a light oil and sli

Seite 2 - VERY IMPORTANT

8. Next, Install Control Rod into Valve Adapter by pressing onto the Valve Adapter located at the back of the sprayer skirt, shown below right. Insta

Seite 3 - Nozzle Installation

PAGE 3For Support for your S25, please contact:nortH ameriCa europe DMMP LimitedT: 0845 643 9776E: [email protected]: www.earthway.co.ukMuggioli Giar

Seite 4 - Before use

How to use your S25 SprayerThe S25 SPRAY-PRO sprayer is designed to be simple to use, easy on the operator and provide years of accurate spraying. The

Seite 5 - After use

How to use the S25 Sprayer - continuedWhen Tank is empty, pull the S25 backwards to prevent and damage to the pump.Technical spray information and how

Seite 6 - OPTIONAL

Liter Gallon2520151052654321361043/16” x 1” Cotter pinABCD4321ABS25 SPRAY-PROS25 SPRAY-PROEarthWayRS25-60000Tank w/CapS25-41000Control RodS25- 2450

Kommentare zu diesen Handbüchern

Keine Kommentare

Earthway S25ss SPRAY-PRO PUSH SPRAYER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Gartengeräte Earthway S25ss SPRAY-PRO PUSH SPRAYER herunter. Earthway S25ss SPRAY-PRO PUSH SPRAYER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Gartengeräte Earthway S25ss SPRAY-PRO PUSH SPRAYER